Washer & Dryer Repair in Revere, MA
Appliance Repair for Homes & Businesses in Revere, Massachusetts and Nearby Areas
Washer and Dryer Repair Services in Revere
Laundry appliances are the workhorses of the home often running daily in large families. Modern machines have evolved from simple mechanical timers to complex units with sensors and logic boards. We provide comprehensive repair services for all configurations of washers and dryers. We understand the specific challenges of laundry closets in condos and basement setups in older homes. We work efficiently to minimize the disruption to your routine.
Laundry systems we work on
- Top load washers with agitators
- High efficiency (HE) top load washers
- Front load washing machines
- Gas dryers (natural gas and propane)
- Electric dryers (240 volt)
- Stacked washer and dryer units
- All in one combo washer dryers
- Compact 24 inch apartment size units
What makes washer and dryer repair tricky
- Balancing mechanisms in high speed spin cycles
- Hidden electronic control boards protected by sealant
- Gas valve coils that fail intermittently
- Complex venting paths in multi story homes
- Direct drive motors versus belt driven systems
- Door boot seals that require special tools to install
- Water level pressure switches and flow meters
- Thermal fuses that blow due to airflow restrictions
Common Washer and Dryer Problems We Fix
Washer will not drain water
This is one of the most common issues we encounter. The cycle finishes but the clothes are soaking wet and there is water standing in the drum. This creates a heavy mess and can lead to odors if not addressed quickly.
Likely causes
- Clogged drain pump filter (coins, socks, lint)
- Failed drain pump motor
- Kinked drain hose behind the unit
- Broken lid switch (some models won’t drain if they think the lid is open)
- Worn belt slipping on the pump pulley
- Control board not sending power to the pump
How we diagnose it
We listen for the hum of the pump motor. If it is silent we check for voltage. If it hums but moves no water we check for physical blockages. We often find small items like baby socks or coins jamming the impeller.
What you can do right now
If your model has a front access filter open it carefully with a towel ready to catch the water. excessive suds can also prevent draining so run a cycle with no detergent if you suspect an overdose.
Washer is shaking or vibrating violently
A walking washer can damage your floor and the machine itself. While some vibration is normal loud banging and movement indicate a suspension failure or an unbalanced load detection error.
Likely causes
- Worn suspension rods or springs
- Broken shock absorbers (front loaders)
- Counterweight has come loose
- Machine is not level on the floor
- Shipping bolts were not removed (on new installs)
How we diagnose it
We press down on the tub to test the rebound of the suspension rods. If the tub bounces like a pogo stick the rods are worn out. We also check the leveling legs to ensure all four are making firm contact with the floor.
What you can do right now
Check if the load is bunched up. Washing a single heavy item like a comforter often causes imbalance. Add some towels to balance the load.
Washer is leaking water
Puddles around the washer are a slip hazard and a risk to your building materials. In second floor laundry rooms in Revere condos a leak can quickly damage the ceiling of the unit below.
Likely causes
- Cracked or loose water supply hoses
- Torn door boot seal (front loaders)
- Internal tub to pump hose leak
- Drain pump housing crack
- Overfilling due to a bad pressure switch
How we diagnose it
We run the machine and watch specifically during the fill and drain cycles. We remove the front or rear panel to trace the path of the water. Rusty trails often lead us to the source of a slow leak.
What you can do right now
Turn off the water supply valves on the wall immediately. Wipe up the water to prevent it from soaking into the subfloor.
Dryer is running but not heating
A dryer that tumbles but stays cold is useless. You end up running the cycle three times just to get damp clothes. This wastes energy and puts unnecessary wear on the motor and rollers.
Likely causes
- Blown thermal fuse (usually due to a clogged vent)
- Burnt out heating element (electric)
- Failed gas valve solenoids (gas)
- Broken igniter
- Tripped circuit breaker (one leg of the 240v)
How we diagnose it
For electric dryers we test the element for continuity. For gas dryers we observe the ignition sequence. If the igniter glows but the gas does not release the solenoids are likely weak.
What you can do right now
Check your lint filter. A completely blocked filter restricts air so much that the safety fuse blows. Also check your breaker panel.
Dryer takes too long to dry
If your dryer heats up but the clothes still take two hours to dry the issue is almost always airflow. The moist air must be exhausted outside for the clothes to dry.
Likely causes
- Clogged dryer vent duct in the wall
- Crushed transition hose behind the dryer
- Blower wheel stripped or clogged with lint
- Moisture sensor strips are dirty
- Vent hood outside is stuck closed
How we diagnose it
We disconnect the vent from the back of the dryer and run a test load. If it dries quickly while venting into the room (temporarily) the problem is in the house ductwork not the machine.
What you can do right now
Go outside and check the vent hood while the dryer is running. You should feel a strong stream of warm air. If the air is weak you likely have a clog in the duct.
Dryer is making loud squeaking or thumping noises
A rhythmic thump or a high pitched squeak indicates mechanical wear. Ignoring this can lead to the drum seizing up completely or the belt snapping.
Likely causes
- Worn out drum support rollers
- Idler pulley bearing failure
- Worn drum glides or slides
- Object stuck in the blower wheel
- Drive belt is frayed
How we diagnose it
We disassemble the cabinet to inspect the rollers. If one roller is bad we typically recommend replacing the whole set since they wear at the same rate.
What you can do right now
Check the inside of the drum for coins or buttons stuck in the baffles. Sometimes the noise is just a loose object tumbling around.
Washer smells like mildew
A foul odor coming from your washer transfers to your clean clothes. This is especially common in front load washers where water can sit in the crevices of the gasket.
Likely causes
- Mold growth behind the door boot seal
- Clogged drain pump filter holding stagnant water
- buildup of detergent and fabric softener
- Drain hose installed without a proper loop
How we diagnose it
We inspect the seal for black spots and check the drain installation. If the drain hose is flat on the floor dirty water can siphon back into the machine.
What you can do right now
Leave the door open after every wash to let the drum dry out. Run a cleaning cycle with a dedicated washer cleaner tablet.
Unit will not start
Dead units are often caused by simple safety switches or power issues. However they can also indicate a main control board failure.
Likely causes
- Broken door strike or lid switch
- Thermal fuse blown
- Control board failure
- Start switch / knob broken
- Power cord damage
How we diagnose it
We use a multimeter to trace the voltage from the wall outlet to the control board. We verify that the door switch is closing the circuit. On many dryers a blown thermal fuse cuts power to the motor entirely.
What you can do right now
Unplug the unit for five minutes to reset the computer. Check that the door is closing firmly and the latch is not bent.
Safety Notes for Washer and Dryer Issues
Washer and dryer repair involves managing three major risks: flooding, fire, and gas leaks. A malfunctioning dryer is a leading cause of house fires due to lint buildup. We prioritize safety in every repair we perform.
In Revere many homes are older wood frame structures or triple deckers where a fire can spread rapidly. This makes dryer safety even more critical. Gas dryers require respect for the fuel source while electric dryers require respect for the 240 volt circuit. Water leaks in multi unit buildings can lead to liability for damage to neighbors. We ensure that every hose is secure and every vent is clear before we finish a job.
Safety checklist for homeowners
- If you smell gas near your dryer turn off the gas valve immediately and open a window. Do not touch any electrical switches.
- If your dryer feels extremely hot on the top cabinet stop using it. This is a sign of restricted airflow and a fire hazard.
- If you see water leaking near electrical outlets turn off the main breaker for the house before stepping in the water.
- If your washer is smoking or making a grinding noise stop the cycle immediately.
- If the breaker for your electric dryer trips repeatedly do not keep resetting it. This indicates a short circuit that needs professional attention.
Brands We Service for Washer and Dryer Repair in Revere
We service a wide variety of laundry appliance brands. From the rugged older units to the newest smart appliances we have the experience to fix them. Each manufacturer uses different drive systems and logic boards so brand specific knowledge is essential.
Whirlpool family (Whirlpool, Maytag, Roper, Amana)
These are the most common units we see. Older models with the “direct drive” system are legendary for durability and are definitely worth repairing. Newer VMW (Vertical Modular Washer) models use different sensors and a belt drive system. Maytag Commercial technology is also popular in this group.
Common issues we see with these models
- Lid lock failure preventing the cycle from starting
- Actuator failure causing the machine not to shift from wash to spin
- Dryer rollers wearing out causing loud rumbling
- Gas valve coils failing after a few minutes of heat
Why correct diagnosis matters
On newer vertical modular washers the “shift actuator” often fails. It can mimic a bad transmission or motor. We know how to test the optical sensor in the actuator to save you from buying an expensive motor you don’t need.
GE family (GE, Hotpoint)
GE washers often use a “Hydrowave” system with a specific motor inverter. Their dryers are generally robust but have long venting runs inside the machine that collect lint. We frequently service top load GE units in rental properties throughout Revere.
Common issues we see with these models
- Motor inverter failure causing the washer not to agitate
- Front load door gasket leaks
- Dryer knob stripping the plastic shaft
- Rear bearing failure in dryers causing squealing
Why correct diagnosis matters
GE top loaders use a blinking LED on the motor to signal error codes. A technician must know how to read this binary code to diagnose the motor issue correctly.
Samsung and LG
These brands dominate the front load market. They are high tech and very water efficient. They use Direct Drive motors attached directly to the drum. While excellent performers they rely heavily on electronics and sensors.
Common issues we see with these models
- Drain pump failure causing OE or 5E codes
- Spider arm (drum support) breaking due to corrosion
- Dryer heating element burning out
- Main control board failures
Why correct diagnosis matters
A “drain error” on these units can sometimes be a bad wire harness rather than the pump itself. We check the resistance at the board to ensure we are fixing the right part.
Speed Queen
Speed Queen is known for commercial grade quality in residential units. They are built simply and heavily. We often see these in homes where durability is the priority. They are rarely broken but when they are it is usually a simple mechanical fix.
Common issues we see with these models
- Belt slipping
- Timer advancing issues
- Water level pressure switch adjustment
Why correct diagnosis matters
Speed Queen parts are specific and distinct from other brands. We appreciate the build quality and know how to maintain it.
Electrolux and Frigidaire
Electrolux front loaders are known for their reversible doors and second floor stability. They are complex machines with advanced balancing technology. Frigidaire laundry centers (stacked units) are very common in Revere apartments.
Common issues we see with these models
- Door latch assembly failure
- Bellows (seal) tearing
- Dryer lint filter housing cracking
- Drain pump obstructions
Why correct diagnosis matters
On stacked laundry centers accessing the components can be difficult. We know the disassembly procedure to reach the washer pump or dryer belt without damaging the cabinetry.
Understanding Common Laundry Error Codes
Modern washers and dryers speak in codes. These digital displays give us a starting point for troubleshooting.
- F7 E1 (Whirlpool): Basket speed sensor fault or shifter issue.
- OL (Whirlpool/Maytag): Overloaded tub.
- UE / uB (Samsung/LG): Unbalanced load error.
- OE / 5E (LG/Samsung): Drain error meaning water is not leaving the tub.
- IE / 4E (LG/Samsung): Water inlet error meaning the machine is not filling.
- F01 (Many brands): Main control board failure.
- F41 (Frigidaire): Control board thinks the door switch is open.
- d80 / d90 (LG Dryer): Airflow restriction in the duct (80% or 90% blocked).
- E64 (Electrolux Dryer): Heater circuit failure.
Maintenance Tips for Washer and Dryer Owners in Revere
Preventative maintenance extends the life of your appliances and prevents disasters. In our coastal environment checking for corrosion on external vents is also a good idea.
Clean the dryer vent annually
This is the most important safety step. A clogged vent is a fire hazard and kills your dryer’s efficiency. Disconnect the hose and vacuum it out. If the run is long hire a professional vent cleaner.
Use HE detergent correctly
Modern washers need very little soap. Two tablespoons is often enough. Using too much creates suds that confuse the sensors and lead to mold growth in the outer tub.
Leave the washer door ajar
After a cycle leave the lid or door open to let the moisture evaporate. This prevents the “gym bag” smell that develops in sealed wet environments.
Check hoses every 5 years
Rubber hoses degrade over time. Replace them with stainless steel braided hoses to prevent burst pipes. This is especially important for units on upper floors.
Clean the lint trap every load
Never skip this. A clean screen improves airflow and drying speed. Wash the screen with soap and water occasionally to remove invisible dryer sheet residue.
Level the machine
If your washer rocks it will damage the suspension. Use a level and adjust the feet until it is solid. Lock the jam nuts against the frame to keep them in place.
Don’t overload
Stuffing the machine full prevents clothes from moving and cleaning properly. It also puts massive strain on the bearings and motor. Two medium loads are better than one giant load.
Service Area for Washer and Dryer Repair in and Around Revere, Massachusetts
We are a local company committed to serving the Revere community. We know the area well from the tight streets of Beachmont to the hills of North Revere. We understand the challenges of moving appliances in triple deckers and narrow condos. We also serve the neighboring towns to ensure our customers have access to reliable service.
- Revere
- Beachmont
- Point of Pines
- Oak Island
- North Revere
- Chelsea
- Winthrop
- Everett
- Malden
- Saugus
Zip codes we serve: 02151
Frequently Asked Questions
Is it worth repairing a 10 year old dryer
Dryers are simple machines and are almost always worth repairing. A new heating element or a set of rollers is a fraction of the cost of a new unit. Washers are more complex but if the repair is minor it is often worth extending the life of the machine.
Why is my dryer getting hot but not drying clothes
This is the classic sign of a vent restriction. The heat is being produced but the moisture laden air cannot escape the drum. Check your vent hose for kinks or clogs. If the vent is clear the blower wheel inside the dryer might be stripped.
Do you work on stackable washer dryer units
Yes we service stacked units and one piece laundry centers. These are common in Revere condos and closets. We have the tools and experience to service them even in tight spaces.
Can I use a flexible foil vent for my dryer
We strongly recommend using semi rigid or rigid metal venting. The white plastic or thin foil vents are fire hazards because they trap lint in their ridges and can crush easily blocking airflow.
Why does my washer smell like sewage
This can happen if the drain hose is pushed too far down into the standpipe or if the p-trap in the wall is dry. It can also be caused by severe mold buildup inside the washer drum.
Is there a washer and dryer repair technician near me in Revere
Yes we are local to Revere and ready to help. Being local means we can respond quickly and we aren’t driving in from out of state.
How long does a repair take
Most laundry repairs are completed in 45 minutes to an hour. We carry belts, pumps, elements, and sensors in our vans. If we need a special board or motor we will schedule a return visit as soon as the part arrives.
Do you fix coin operated laundry machines
We primarily focus on residential equipment. If you have a residential style machine that happens to have a coin slide (like in a small landlord owned multi family) we may be able to help but we do not service large commercial laundromat equipment.
What causes small holes in my clothes after washing
This is often caused by a foreign object stuck in the drum holes like a bra underwire or a screw. It can also be caused by aggressive agitation or using bleach directly on the fabric.
Why is my front load washer vibrating so much
Front loaders spin at very high speeds. If the machine is not perfectly level or if the floor is not stable (like on a second floor) it will vibrate. Shock absorbers also wear out over time and need replacement.
Can you reverse the door on my dryer
Yes most dryer doors are reversible. If the door swing is awkward for your laundry room layout we can flip it for you during a service call.
What does it mean if my gas dryer clicks but doesn’t light
This usually indicates weak gas valve coils. The coils open the valve to let gas flow. When they get weak they might open once and then fail to open again causing the flame to go out.
Conclusion
Appliance Repair Pros is dedicated to keeping the laundry rooms of Revere functioning efficiently. We know that a broken washer or dryer disrupts your entire week. Whether you have a simple belt failure or a complex electronic issue our technicians have the expertise to fix it. We serve our neighbors in Oak Island, Chelsea, and beyond with honest reliable work. Don’t let the laundry pile up any longer.
Contact us today for professional washer and dryer repair.